收藏本站
MC3423
APPLICATION INFORMATION
Basic Circuit Configuration
The basic circuit configuration of the MC3423 OVP is
shown in Figure 3 for supply voltages from 4.5 V to 36 V,
and in Figure 4 for trip voltages above 36 V. The threshold
(+ Sense
Lead)
1
+
or trip voltage at which the MC3423 will trigger and supply
gate drive to the crowbar SCR, Q1, is determined by the
selection of R1 and R2. Their values can be determined by
the equation given in Figures 3 and 4, or by the graph shown
in Figure 8. The minimum value of the gate current limiting
resistor, R G , is given in Figure 9. Using this value of R G , the
SCR, Q1, will receive the greatest gate current possible
Power
Supply
Z1
R1
R2
2
5
1k
4 3
MC3423
7
C
8 R G
without damaging the MC3423. If lower output currents
are required, R G can be increased in value. The switch, S1,
shown in Figure 3 may be used to reset the crowbar.
Otherwise, the power supply, across which the SCR is
connected, must be shut down to reset the crowbar. If a non
current?limited supply is used, a fuse or circuit breaker, F1,
should be used to protect the SCR and/or the load.
The circuit configurations shown in Figures 3 and 4 will
have a typical propagating delay of 1.0 m s. If faster
(? Sense Lead)
Figure 7. Configuration for Programmable
Duration of Overvoltage Condition Before
Trip/With Immediate Trip at
High Overvoltages
?
operation is desired, Pin 3 may be connected to Pin 2 with
Pin 4 left floating. This will result in decreasing the
propagating delay to approximately 0.5 m s at the expense
of a slightly increased TC for the trip voltage value.
Configuration for Programmable Minimum Duration
of Overvoltage Condition Before Tripping
In many instances, the MC3423 OVP will be used in a
noise environment. To prevent false tripping of the OVP
circuit by noise which would not normally harm the load,
MC3423 has a programmable delay feature. To implement
this feature, the circuit configuration of Figure 5 is used. In
this configuration, a capacitor is connected from Pin 3 to
V EE . The value of this capacitor determines the minimum
duration of the overvoltage condition which is necessary to
trip the OVP. The value of C can be found from Figure 10.
The circuit operates in the following manner: When V CC
rises above the trip point set by R1 and R2, an internal
current source (Pin 4) begins charging the capacitor, C,
connected to Pin 3. If the overvoltage condition disappears
before this occurs, the capacitor is discharged at a rate ? 10
times faster than the charging rate, resetting the timing
feature until the next overvoltage condition occurs.
Occasionally, it is desired that immediate crowbarring of
the supply occur when a high overvoltage condition occurs,
while retaining the false tripping immunity of Figure 5. In
this case, the circuit of Figure 6 can be used. The circuit will
operate as previously described for small overvoltages, but
will immediately trip if the power supply voltage exceeds
V Z1 + 1.4 V.
Additional Features
1. Activation Indication Output
An additional output for use as an indicator of OVP
activation is provided by the MC3423. This output is an
open collector transistor which saturates when the OVP
is activated. In addition, it can be used to clock an edge
triggered flip?flop whose output inhibits or shuts down
the power supply when the OVP trips. This reduces or
eliminates the heatsinking requirements for the crowbar
SCR.
2. Remote Activation Input
Another feature of the MC3423 is its remote
activation input, Pin 5. If the voltage on this CMOS/TTL
compatible input is held below 0.8 V, the MC3423
operates normally. However, if it is raised to a voltage
above 2.0 V, the OVP output is activated independent of
whether or not an overvoltage condition is present. It
should be noted that Pin 5 has an internal pullup current
source. This feature can be used to accomplish an
orderly and sequenced shutdown of system power
supplies during a system fault condition. In addition, the
activation indication output of one MC3423 can be used
to activate another MC3423 if a single transistor inverter
is used to interface the former ’s indication output to the
latter ’s remote activation input, as shown in Figure 7. In
this circuit, the indication output (Pin 6) of the MC3423
on power supply 1 is used to activate the MC3423
associated with power supply 2. Q1 is any small PNP
with adequate voltage rating.
http://onsemi.com
4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MCIMX51LCD DAUGHTER LCD WVGA I.MX51
MCP1630DM-NMC1 BOARD DEMO FOR MCP1630
MCP1630RD-LIC1 REFERENCE DESIGN FOR MCP1630
MCP1630RD-NMC1 REF DESIGN MCP1630 NIMH BATT CHG
MCP212XEV-DB BOARD DEMO FOR MCP212X
MCP215X/40EV-DB BOARD DEMO FOR MCP215X/40
MCP215XDM BOARD DEMO FOR MCP215X
MCP23X08EV BOARD EVALUATION FOR MCP23X08
相关代理商/技术参数
MC3423P 制造商:Motorola Inc 功能描述:
MC3423P1 功能描述:监控电路 6.5V OverVoltage RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MC3423P1G 功能描述:监控电路 6.5V OverVoltage Crowbar Sensing RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MC3423P1G 制造商:ON Semiconductor 功能描述:Voltage Regulator IC Voltage Regulator T
MC34242 制造商:SPC Multicomp 功能描述:FINGER GUARD 制造商:SPC Multicomp 功能描述:FINGER GUARD; For Use With:40mm Axial Fans; Fan Size:40 x 40mm; Fixing Centers:32mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Black; External Depth:4.8mm; External Height:28.9mm; External Width:28.9mm; Material:Steel ;RoHS Compliant: Yes
MC34243 制造商:SPC Multicomp 功能描述:FINGER GUARD 制造商:SPC Multicomp 功能描述:FINGER GUARD; For Use With:50mm Axial Fans; Fan Size:50 x 50mm; Fixing Centers:40mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Black; External Depth:4.8mm; External Height:41.1mm; External Width:41.1mm; Material:Steel ;RoHS Compliant: Yes
MC34245 制造商:SPC Multicomp 功能描述:FINGER GUARD 制造商:SPC Multicomp 功能描述:FINGER GUARD; For Use With:50mm Axial Fans; Fan Size:50 x 50mm; Fixing Centers:40mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Black; External Depth:4.8mm; External Height:41.1mm; External Width:41.1mm; Material:Steel ;RoHS Compliant: Yes
MC34249 制造商:SPC Multicomp 功能描述:FINGER GUARD 制造商:SPC Multicomp 功能描述:FINGER GUARD; For Use With:60mm Axial Fans; Fan Size:60mm; Fixing Centers:50mm; Guard Material:Steel; Accessory Type:Finger Guard; Color:Black; External Depth:4.4mm; External Height:53.2mm; External Width:53.2mm; Material:Steel ;RoHS Compliant: Yes